عفوا ,,, لايمكنك مشاهده الروابط لانك غير مسجل لدينا [ للتسجيل اضغط هنا ]
Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000′.
To resurrect HTC Droid Eris:

  • Solder JTAG cable to HTC Droid Eris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Droid Eris is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
  • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

عفوا ,,, لايمكنك مشاهده الروابط لانك غير مسجل لدينا [ للتسجيل اضغط هنا ]
Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000′.


To resurrect HTC Polaris:


  • Solder JTAG cable to HTC Polaris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Polaris selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

عفوا ,,, لايمكنك مشاهده الروابط لانك غير مسجل لدينا [ للتسجيل اضغط هنا ]


  • QSC1100_X14_NOR,
  • QSC60XX_L18_D08_NOR,
  • QSC60XX_L20_D08_NOR,
  • QSC60XX_L24_D08_NOR

Whats new:

  • Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)

This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.

عفوا ,,, لايمكنك مشاهده الروابط لانك غير مسجل لدينا [ للتسجيل اضغط هنا ]

Firmware 1.22
---------------------------

  • Fixed bugs in ARM7 core handling routines



JTAG Manager 1.30
---------------------------

  • Added DISABLE_POLLING request processing from DCC Loader

(used by DCC Loaders which have small RAM size available and there is no DCC RX polling is implemented in RIFFBOX firmware for current core);

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.